Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Hialeah Owner’s Guide

We stock and install Ghost Controls-compatible keypad and intercom repairs in Hialeah, with most completed jobs running $180-$340 installed depending on whether the issue is a standalone keypad, a wired intercom station, or a combined entry system with integrated relay. Same-day service is available when the part is already on our van, which it usually is for the common Ghost Controls AXWK and WKAX series housings. Most Hialeah owners figure out something’s wrong when the gate stops responding to PIN entry but still works fine from the remote, or when visitors press the call button and nothing reaches the house.

Call (786) 458-8210

Which Ghost Controls Models This Applies To

Ghost Controls keypads and intercoms fall into a few distinct product families, and matching the right repair means reading the label inside the battery compartment or on the back of the mounted unit. The AXWK wireless keypad and WKAX wired keypad are the two we see most often on Hialeah properties, typically paired with TSS1 or TDS2 operators on single or dual swing gates. The intercom line, including the GSM-intercom variants, shares some housing dimensions with the keypads but uses different internal relay boards and weather-sealing.

Here’s the compatibility gotcha: Ghost Controls changed the mounting footprint between the 2018-2020 production run and the current generation. The screw holes shifted roughly three-eighths of an inch, so an owner who pulls a dead unit and orders a replacement by sight alone often ends up drilling new holes in a stucco pillar or fabricating a plate. We carry adapter brackets for both footprints on the van, and we check the part number against the operator’s control board before we quote. For Ghost Controls specifically, we source OEM housings and membrane pads when they’re available, but we’ve also validated a commercial-grade aftermarket keypad from Linear that speaks the same 433 MHz frequency and holds up better in Hialeah’s salt-air humidity. The choice depends on whether you want the Ghost Controls logo on the button pad or you want the unit that survived our bench test at 95 percent humidity for 72 hours.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Intermittent PIN response or multiple presses required. The membrane switch beneath the buttons degrades from UV exposure and humidity cycling. In Hialeah, we see this accelerate on west-facing pillars where afternoon sun hits the keypad directly, typically starting around the 3-year mark.
• Backlight works but no relay click at the gate operator. The keypad’s internal radio or hardwire connection is intact, but the output relay has fused contacts or corrosion. This is a board-level repair on some units, a full housing swap on others.
• Intercom call button lights up, no audio or no indoor chime. The speaker or microphone element has failed from moisture intrusion, or the two-wire loop to the house has a break. We test the loop with a tone generator before we quote a part replacement.
• Keypad powers on briefly, then dies in cold mornings. The lithium battery pack in wireless units loses capacity; in wired units, this pattern points to a failing voltage regulator on the keypad board. Either way, the unit needs more than fresh batteries.
• Visible corrosion on the terminal block or antenna pigtail. Hialeah’s wet season pushes moisture through the gasket over time. Once green copper oxide appears on the antenna connection, signal range drops before total failure follows.

Before

After

Replacement Cost & What’s Included

What moves the number: whether the existing conduit is reusable, whether the stucco or stone pillar needs anchor repair, and whether the operator’s control board requires a factory reset to pair the new device. We write the exact price on a scope sheet before any work starts, under Haven Standard Clause 1. Every repair carries our 365-Day Done Right Promise, and under Clause 4, you get a photographed record of the wiring before and after, the part number installed, and the limit or frequency settings we programmed.

DIY or Call Us?

There’s a safe middle ground here. A homeowner can check the battery voltage with a multimeter, verify the breaker hasn’t tripped, and confirm the antenna pigtail hasn’t wiggled loose. Those three checks solve about 15 percent of the calls we get.

Where DIY goes wrong: programming a new Ghost Controls keypad requires putting the operator into learn mode, which means accessing the control board inside the operator housing. That board sits inches from the 120 VAC terminal strip and the capacitor bank. If you haven’t locked out the disconnect and verified zero energy, you’re working live on a wet metal box in Hialeah humidity. We don’t recommend it. The relay programming also isn’t intuitive, Ghost Controls uses a timed-sequence entry that trips up most first attempts and can lock out the operator’s existing remotes if done wrong. We carry the right tools, we’ve done the sequence hundreds of times, and we document what we set so the next technician isn’t guessing. Name what you found. Name what it costs. Name what you left behind.

If you’re stuck at any point, call (786) 458-8210. A live person answers, and we’ll walk through what you’re seeing before we dispatch.

FAQs